HDPE / PP TARPAULIN
We have the infrastructure to manufacture wide range of tarpaulins in various GSM, Size and colours.
These Waterproof Tarpaulin is manufactured with pure raw materials with UV stabilizer for longer life, under constant exposure to sunlight. These tarpaulins are available in various sizes and dimensions and can be customized to suit the requirements of the clients
Tarpaulin is widely used in Rain Water Protection in Sheds, Transportation, Trucks & Other auto mobiles, Storage godowns, Boats, Snowmobiles, Plant & Machinery, Construction sites, Lumber, Grain, Temporary Storages, Tents, Ground Sheets, and more.
- Lightweight & easy to handle
- Reinforced edges , grommets on sides & corners
- Puncture resistant
- Flame Retardant
- Shrink Proof
Plastic Sheets / Plastic Tarpaulin ( IOM / IFRC/ ICRC)
|Width and length|
|Size / sheet||4.00 m x 6.00 m +- 1|
|Size / roll||4.00 m x 60.00 m +- 1|
|Specific sheet without bands weight||190 +- 20g under ISO 3801 (equivalent to 170 gsm min to 210 gsm max)|
|Complete sheet with bands weight||Plain sheet specific weight plus 10% additional weight for reinforcement bands
under ISO 3801
|Total weight||From 187 gsm min to 231 gsm max. Specific weight of bands from
150 gsm min to 200 gsm max.
|Sheet / roll||Woven HDPE black fibres fabric, double-side lamination with LDPE coating, reinforced
with six bands of 75 mm width woven black HDPE fibres fabric and coated outside.
Pre-punched 8 mm holes on the two side bands at 0.1 m +/-10% intervals, positioned in the
centre of the bands (only the reinforcement bands are pre-punched, not the tarpaulin itself).
|Tensile strength||Min 500 N, 15-25% elongation in warp and weft in plain sheet under ISO 1421-1|
|UV resistance||After 1500 hours UV under ASTM G53/94 (UVB 313 nm peak) minimum 80% of original
value of the actual product and not less than 475 N
|Reinforcement bands||Min 700 N as per ISO 1421-1, pulling lengthwise in a prepunched 8 mm hole with a hook
of 8 mm wire diameter, at 200 mm from the end of the band. UV resistance80% of original
value and not less than 665 N.
|Welding||Only one is allowed, lengthwise. The tarpaulin tensile strength crossways at the place
of welding under ISO 1421-1 minimum 50% of original value and not less than 400 N
Plastic Sheets / Plastic Tarpaulin ( UNHCR / UNICEFF)
|Width and length|
|Size / sheet||4.00 m x 5.00 m +- 1|
|Size / roll||4.00 m x 50.00 m +- 1|
|Sheet / roll||190 gsm ±20 g/m² woven Polyethylene (HDPE) inner black fibers, warp x weft,
laminated on both sides with LDPE coating
|Tensile strength||Min 600N both directions warp and weft (BS 2576, 50mm grab test or equivalent)|
|Tear strength||Min 100N both directions (BS 4303 wing tear or equivalent) or under ISO 4674 (A2)|
|UV resistance||Max 5% loss of original tensile strength under ISO 1421 after 1500 hours UV under ASTM
G53/94 (UVB 313nm peak)
|Welding||Only 1 is allowed, lengthwise. Min resistance 80% of original tarpaulin tensile strength in
the weft under ISO 1421 plus additional procedure
|Eyelets||Aluminum reinforcement eyelets or equivalent on 4 sheet sides of single sheets at 100cm (±5 cm) Centre to Centre, providing very strong fixation|
- Reinforced plastic tarpaulin in 4 m x 5 m sheets or 4 m x 50 m rolls developed by international research project and designed for long outdoor use in all climates
- Made of woven high density black polyethylene (HDPE) fibres, warp x weft, laminated on both sides with low density polyethylene (LDPE) coating
- Highly recommended for family shelter protection